Profile optimization parameters
From Opera Wiki
(Difference between revisions)
(Created page with '{{WIP}} {{BR}} <!-- HELP: JM/W2901 --> Category: JM/Manual') |
|||
| (9 intermediate revisions not shown) | |||
| Line 1: | Line 1: | ||
| - | {{ | + | [[File:quadroparametriottimizzazione.png|thumb|right|500px|Optimization parameters]] |
| + | {{NB|To access this window: from ''Profiles'' select [[Image:tastoottimizza.png]] button}} | ||
| + | |||
| + | This window is used to customize the optimization data for a profile. | ||
| + | |||
| + | '''Content description''' | ||
| + | |||
| + | *'''Min waste''': the minimum allowed waste for the profile | ||
| + | *'''Min waste offcut''': the maximum waste during the optimization of the offcuts | ||
| + | *'''Cut priority''': sort position for the cutting list | ||
| + | *'''Force group bar''': if enabled, bars are cut together even when more bars than necessary are required | ||
| + | *'''N. of assembled parts''': the number of bars to cut together | ||
| + | <!-- | ||
| + | {|style=float:left | ||
| + | |[[File:taglioott.png|thumb|left|300px|Esempio di taglio ottimizzato con 1 pezzo accorpato e la casella Forza barre insieme disattiva]] | ||
| + | |[[File:taglioott2.png|thumb|left|300px|Esempio di taglio ottimizzato con 2 pezzi accorpati e la casella Forza barre insieme attiva]] | ||
| + | |} | ||
| + | |||
{{BR}} | {{BR}} | ||
| + | --> | ||
| + | *'''Re-usable leftover''': the minimum lenght of the leftover to utilize again | ||
| + | *'''Do not divide long pieces''': If enabled, long workpieces are not shared out amid the bars to be optimized | ||
| + | *'''Unique label pack''': If enabled, Opera will print out a unique label for the grouped cut | ||
| + | |||
| + | {{NB| The following settings are available only when Opera Smart Optimization is installed}} | ||
| + | |||
| + | *'''Type'''[[File:frecciagiu.png]]: the tipe of bar optimization | ||
| + | **'''None''': do not use any optimization on bars | ||
| + | **'''Interval''': :Choosing this kind of optimization, it’s possible to determine both the minimal and the maximal measure put on disposal by the supplier, and a step of change of the optimization measures. Following this procedure the program draws the best possible measure for the needed bar. | ||
| + | <!--[[File:taglioott3.png|thumb|right|300px|Esempio di Taglio ottimizzato al pezzo]]--> | ||
| + | **'''List''':This allows to create a list of maximal measures put on disposal by the supplier. Such measures are analyzed by the program which will take the fittest bar to order in the optimization stage. | ||
| + | **'''Per part''': This allow to optimize and hence to order the bar, in the real measure of use | ||
| + | |||
<!-- HELP: JM/W2901 --> | <!-- HELP: JM/W2901 --> | ||
[[Category: JM/Manual]] | [[Category: JM/Manual]] | ||
Latest revision as of 14:13, 16 May 2011
N.B: To access this window: from Profiles select 
buttonThis window is used to customize the optimization data for a profile.
Content description
- Min waste: the minimum allowed waste for the profile
- Min waste offcut: the maximum waste during the optimization of the offcuts
- Cut priority: sort position for the cutting list
- Force group bar: if enabled, bars are cut together even when more bars than necessary are required
- N. of assembled parts: the number of bars to cut together
- Re-usable leftover: the minimum lenght of the leftover to utilize again
- Do not divide long pieces: If enabled, long workpieces are not shared out amid the bars to be optimized
- Unique label pack: If enabled, Opera will print out a unique label for the grouped cut
N.B: The following settings are available only when Opera Smart Optimization is installed- Type
: the tipe of bar optimization
- None: do not use any optimization on bars
- Interval: :Choosing this kind of optimization, it’s possible to determine both the minimal and the maximal measure put on disposal by the supplier, and a step of change of the optimization measures. Following this procedure the program draws the best possible measure for the needed bar.
- List:This allows to create a list of maximal measures put on disposal by the supplier. Such measures are analyzed by the program which will take the fittest bar to order in the optimization stage.
- Per part: This allow to optimize and hence to order the bar, in the real measure of use
