From Opera Wiki

(Difference between revisions)

Revision as of 08:16, 29 May 2026

Filling archive

N.B: To access this window in Opera Job Management: from the Archives menu, select the Fillings button.

The Filling archive allows you to configure the filling kits used in types, defining the system and series they belong to, the application type, glass space, glazing beads, gaskets, and the conditions for automatic selection.

Through this archive, it is possible to create complete kits for glass, panels, infill panels, and specific solutions, associating the materials required for the filling and defining the rules according to which the program proposes or applies them automatically in type management.

Section 0: filter fields

The upper part of the window contains the fields used to filter the list of filling kits in the archive.

System: allows you to filter fillings according to the selected system.
Series: allows you to filter fillings according to the selected series.
Type: allows you to filter fillings according to the application type.
Min. glass space: allows you to indicate the minimum glass space value to be used as a search criterion.
Max. glass space: allows you to indicate the maximum glass space value to be used as a search criterion.
Price list revision: allows you to filter fillings according to the price list revision.
Key: allows you to search for fillings using an identification key.

Section 1: list of fillings

The left side of the window contains the list of filling kits stored in the archive.

By selecting an item in the list, the main data of the kit are shown on the right side, while the associated components, such as glass, gaskets, glazing beads, or cavities, are displayed in the lower-left part.

Section 2: archive function buttons

The buttons on the side bar allow you to manage the archive records:

Insert: allows you to insert a new filling kit.
Delete: allows you to delete the selected filling kit.
Modify: allows you to modify the data of the selected filling kit.
Copy: allows you to duplicate the selected kit.
Print: allows you to print the list or the data relating to the fillings.
Catalog: opens the Technical catalog management window, which allows you to insert the catalog page or technical data sheet of the filling kit.
Table: allows you to view the data in table form.
OK: confirms the selection or the operation in progress.

Section 3: main filling data

This section defines the identification data of the filling kit.

Name: identification code of the filling kit.
System : system to which the filling kit is associated.
Series : series to which the filling kit is associated.
Desc.: description of the filling kit.
Key: search or classification key of the kit.

Section 4: filling type

The Type field allows you to define the application logic of the filling kit.

The drop-down menu contains the following items:

With glazing bead: select this item if it is a filling that also includes the glazing beads. When this option is selected, the Gb type field is also shown.
Slide-in: select this item if it is a filling that does not include glazing beads, but must be mounted on slide-in glass types.
Push-in: select this item if it is a filling that does not include glazing beads, but must be mounted on push-in glass types.
Glass: select this item if it is a filling that includes only and exclusively the glass or panel.
Cover: select this item if it is a filling for a roller shutter box cover.
Curtain wall: select this item if it is a filling for a curtain wall.

Section 5: glazing bead and glass space parameters

This section allows you to configure the information relating to the glazing bead and the glass space required for the kit.

Gb type: allows you to display the type of glazing bead used in the kit. The field is shown when the With glazing bead item is selected in the Type field.
Glass space: allows you to indicate the glass space required for the filling kit.
Glazing bead group: allows you to display the glazing bead group set in the glazing bead archive.

Section 6: automatic filling selection

This section contains the parameters that regulate the use of the kit in the automatic selection of the glazing bead and filling.

Participates in automatic selection: activating this field enables the use of the filling kit in the automatic selection of the glazing bead.
Automatic search: if activated, it automatically applies the kit once the glass is selected in filling management.
Minimum glass thickness: allows you to indicate the minimum glass thickness for the automatic selection of the filling kit.
Maximum glass thickness: allows you to indicate the maximum glass thickness for the automatic selection of the filling kit.
Filling variable: field used by the program to assign the value from the Vr variable to be used in the conditions.
Automatic selection search keys: allows you to indicate the keys used by the program for the automatic search of the kit.

Section 7: cavities and orientation

This section defines the rules relating to cavities and the orientation of the filling.

Lower cavity from profile: if activated, it imports the lower cavity from the lower profile.
Upper cavity from profile: if activated, it imports the upper cavity from the upper profile.
Orientation: allows you to define the orientation of the filling kit (useful for slatted fillings).

Section 8: impossible filling and message

These fields allow you to manage a dedicated configuration for solutions that cannot be produced.

Impossible filling: allows you to create a specific kit for an impossible solution.
Message: text of the error message shown when a filling configured as impossible is used.

N.B: The function can be used to warn the operator when a specific combination of glass, profile, or glazing bead cannot be applied.

Section 9: bottom buttons

The lower part of the window contains the buttons for managing the materials and the image associated with the kit.

Management: allows the insertion or modification of the materials of the filling, such as glass, gaskets, glazing beads, and other kit components.
Icon: allows you to load a standard image for the selected kit. See How to insert an icon.

Section 10: data registration

After entering or modifying the data, use the buttons at the bottom right:

Register: saves the entered or modified data.
Cancel: cancels the operation in progress without saving the changes.

Related pages

@@ Line 1: / Line 1: @@
-__TOC__
+= Filling archive =
+[[File:Finestraarchivioriempimenti.png|thumb|600px|Filling archive]]
+{{NB|To access this window in Opera Job Management: from the ''Archives'' menu, select the ''Fillings'' button.}}
-{{NB|To access this window from Opera Job Management: open ''Options'' menu, then select ''Backup copies''}}
+The '''Filling archive''' allows you to configure the filling kits used in types, defining the system and series they belong to, the application type, glass space, glazing beads, gaskets, and the conditions for automatic selection.
+Through this archive, it is possible to create complete kits for glass, panels, infill panels, and specific solutions, associating the materials required for the [[type fillings|filling]] and defining the rules according to which the program proposes or applies them automatically in type management.
-== Content description ==
+{{BR}}
-This function is necessary to make backup copies
+== Section 0: filter fields ==
-We strongly suggest making backup copies at least once a day to avoid the unrecoverable loss of data (profiles, typologies, work orders...).  The loss of data can be caused by a sudden breakdown of the computer, or by a virus program that has unrecoverably damaged the data, or by a fault to the hard disk, or by other reasons.  In all of these cases, the data cannot be recovered without the backup copies and therefore it is not possible to start work again. On the contrary, with backup copies, it would just be a matter of restoring them on the hardware in order to begin work again.
+The upper part of the window contains the fields used to filter the list of filling kits in the archive.
-When this function is started, the following message will appear:
+* '''System''': allows you to filter fillings according to the selected system.
-[[Image:messagggiocreazionecopie.png|thumb|left|300px]]
+* '''Series''': allows you to filter fillings according to the selected series.
-{{BR}}
+* '''Type''': allows you to filter fillings according to the application type.
-[[Image:finestraselezionearchivi.png|thumb|left|500px]]
+* '''Min. glass space''': allows you to indicate the minimum glass space value to be used as a search criterion.
-{{BR}}
+* '''Max. glass space''': allows you to indicate the maximum glass space value to be used as a search criterion.
-*[[File:file.png]]: saves a backup to the selected file on disc.
+* '''Price list revision''': allows you to filter fillings according to the price list revision.
-*[[File:local.png]]: creates a backup copy on the hard disk,in the Backup folder located under Opera folder.
+* '''Key''': allows you to search for fillings using an identification key.
-*[[File:file.png]]: opens the browse folder where the backup will be saved.
+== Section 1: list of fillings ==
+The left side of the window contains the list of filling kits stored in the archive.
+By selecting an item in the list, the main data of the kit are shown on the right side, while the associated components, such as glass, gaskets, glazing beads, or cavities, are displayed in the lower-left part.
+== Section 2: archive function buttons ==
+The buttons on the side bar allow you to manage the archive records:
+* [[File:tastopiu.png]] '''Insert''': allows you to insert a new filling kit.
+* [[File:tastomeno.png]] '''Delete''': allows you to delete the selected filling kit.
+* [[File:tastodiverso.png]] '''Modify''': allows you to modify the data of the selected filling kit.
+* [[File:tastouguale.png]] '''Copy''': allows you to duplicate the selected kit.
+* [[File:tastostampa2.png]] '''Print''': allows you to print the list or the data relating to the fillings.
+* [[File:tastocataloghi.png]] '''Catalog''': opens the [[Technical catalogs|Technical catalog management]] window, which allows you to insert the catalog page or technical data sheet of the filling kit.
+* [[File:tastoexcel.png]] '''Table''': allows you to view the data in table form.
+* '''OK''': confirms the selection or the operation in progress.
+== Section 3: main filling data ==
+This section defines the identification data of the filling kit.
+* '''Name''': identification code of the filling kit.
+* '''System''' [[File:tastoc.png]]: system to which the filling kit is associated.
+* '''Series''' [[File:tastoc.png]]: series to which the filling kit is associated.
+* '''Desc.''': description of the filling kit.
+* '''Key''': search or classification key of the kit.
+== Section 4: filling type ==
+The '''Type''' field allows you to define the application logic of the filling kit.
+The drop-down menu contains the following items:
+* '''With glazing bead''': select this item if it is a filling that also includes the glazing beads. When this option is selected, the '''Gb type''' field is also shown.
+* '''Slide-in''': select this item if it is a filling that does not include glazing beads, but must be mounted on slide-in glass types.
+* '''Push-in''': select this item if it is a filling that does not include glazing beads, but must be mounted on push-in glass types.
+* '''Glass''': select this item if it is a filling that includes only and exclusively the glass or panel.
+* '''Cover''': select this item if it is a filling for a roller shutter box cover.
+* '''Curtain wall''': select this item if it is a filling for a curtain wall.
+== Section 5: glazing bead and glass space parameters ==
+This section allows you to configure the information relating to the glazing bead and the glass space required for the kit.
+* '''Gb type''': allows you to display the type of glazing bead used in the kit. The field is shown when the '''With glazing bead''' item is selected in the '''Type''' field.
+* '''Glass space''': allows you to indicate the glass space required for the filling kit.
+* '''Glazing bead group''': allows you to display the glazing bead group set in the glazing bead archive.
+== Section 6: automatic filling selection ==
+This section contains the parameters that regulate the use of the kit in the automatic selection of the glazing bead and filling.
+* '''Participates in automatic selection''': activating this field enables the use of the filling kit in the automatic selection of the glazing bead.
+* '''Automatic search''': if activated, it automatically applies the kit once the glass is selected in filling management.
+* '''Minimum glass thickness''': allows you to indicate the minimum glass thickness for the automatic selection of the filling kit.
+* '''Maximum glass thickness''': allows you to indicate the maximum glass thickness for the automatic selection of the filling kit.
+* '''Filling variable''': field used by the program to assign the value from the Vr variable to be used in the conditions.
+* '''Automatic selection search keys''': allows you to indicate the keys used by the program for the automatic search of the kit.
+== Section 7: cavities and orientation ==
+This section defines the rules relating to cavities and the orientation of the filling.
+* '''Lower cavity from profile''': if activated, it imports the lower cavity from the lower profile.
+* '''Upper cavity from profile''': if activated, it imports the upper cavity from the upper profile.
+* '''Orientation''': allows you to define the orientation of the filling kit (useful for slatted fillings).
+== Section 8: impossible filling and message ==
+These fields allow you to manage a dedicated configuration for solutions that cannot be produced.
+* '''Impossible filling''': allows you to create a specific kit for an impossible solution.
+* '''Message''': text of the error message shown when a filling configured as impossible is used.
+{{NB|The function can be used to warn the operator when a specific combination of glass, profile, or glazing bead cannot be applied.}}
+== Section 9: bottom buttons ==
+The lower part of the window contains the buttons for managing the materials and the image associated with the kit.
+* [[File:tastogestione2.png]] '''Management''': allows the insertion or modification of the materials of the [[type fillings|filling]], such as glass, gaskets, glazing beads, and other kit components.
+* [[File:tastoicona.png]] '''Icon''': allows you to load a standard image for the selected kit. See [[Profile_sections#Inserting_a_new_section|How to insert an icon]].
-* [[File:tastocopiatotale.png]]:  starts the total backup process.
+== Section 10: data registration ==
-* [[File:tastoattivatutti.png]] [[File:tastodisattivatutti.png]]:  these buttons enable or disable all archives.
+After entering or modifying the data, use the buttons at the bottom right:
-== Related items ==
+* '''Register''': saves the entered or modified data.
-*[[Cloud_backups]]
+* '''Cancel''': cancels the operation in progress without saving the changes.
+== Related pages ==
+* [[type fillings|Type fillings]]
+* [[Profile_sections#Inserting_a_new_section|How to insert an icon]]
-[[Category:JM/Manual]]
+[[Category: JM/Manual]]
-[[Category:CAM/Manual]]
 <!-- HELP: JM/W100016,CAM/W100016 -->

Backup copies