Appendix III: the variables and symbols

From Opera Wiki

Variables

To obtain the insertion of the most suitable accessory, detecting it from an autoselection, to insert the correct end shutter slat, to determine the insertion of profile components, depending on specific measurements, or the last slat with the trim dimension, for all these applications and others, as you know, it is often necessary to make use of the potential of the so-called Variables.

The complete list of variables is given below:

Nome	Description
A	No. of the sash to which the profile or accessory belongs. A=0 is the fixed frame, A=1 is the first sash from the left, A=2 is the second sash from the left, etc...
A1	Left or lower cutting angle of the profile to which the formula is applied or the profile to which the accessory is matched. Vale 45° or 90°.
A2	Right or sup. cutting angle of the profile to which the formula is applied or the profile to which the accessory is matched. Vale 45° or 90°.
Alt	Matching profile height
Ap	Toward the opening of the structure. Ap=1 is opening to the left; Ap=2 is opening to the right.
Av	Glass wing size.
Bin	Track (applicable to sliding types).
Cam	Profile room value, as recorded on file.
Comp	Slat compensation quota
Fa	Alternative face.
H	Height of the whole type.
Ha	Sash height at outer tips.
Hav	Rolling height.
Hf	Height of individual structure net of glass rebates.
Hia	Sash height net of rebates.
His	Height of the individual structure net of rebates.
Hs	Height of the single structure.
Hsa	Door mirror height
Hsp	Height of the mounting area of the glass or panel (mirroring).
Hsr	Height of the lock.
Ht	Traverse height
Ht2	Traverse height
Hta	Sash height net of rebates and tooth.
Hts	Height of individual structure net of rebates and tooth.
L	Width of the whole type.
La	Sash width at outer tips.
Lato	Side of the structure to which the formula refers. (Side=1 left; Side=2 right; Side=3 high; Side=4 low)
Lav	Roll-up width.
Lf	Width of the single structure net of glass stops.
Li	Length at the tubularity (i.e., net of the stop and tooth) of the profile to which the formula is applied.
Lia	Sash width net of rebates.
Lis	Width of individual structure net of stops.
Lp	Length at the outer tips of the profile to which the formula is applied.
Ls	Width of the single structure.
Lsa	Door mirror width.
Lsp	Width of the mounting area of the glass or panel (mirroring).
Lt	Value related to the obtained cut length.
Lta	Sash width net of rebates and tooth.
Lts	Width of individual structure net of stops and tooth.
N	Accessory number. Present for compatibility with the industrial production version, not active in the basic version.
Na	Number of sashes holding the structure.
Nst	Number of slats contained in the shutter.
Pa	Total door weight.
Pav	Shutter weight, detects the total weight of the shutter.
Pm	Upright position
Pm3	Upright position.
Pos	Accessory mounting position. Present for compatibility with the industrial production version, not active in the basic version.
Posp	Position profile.
Pt	Total frame weight.
Pz	Total pieces.
Qt	Fee calculated by the program. Present for compatibility with the industrial production version, not active in the basic version.
Qt	Fee calculated by the program. Present for compatibility with the industrial production version, not active in the basic version.
Quad	Square footage of the structure.
Rdo	Remainder staves, detects the trim measurement of the last stave.
Rif	Reference.
Rst	Remaining slats, i.e., it is the value remaining after mounting the shutter slats, allows you to determine which end slat you need to mount.
Sav	Rolling area, detects the measurement of the rolling area.
Spes	Matched profile thickness.
Spr	Filling thickness.
Sr	Deviation match.
TA1	Left corner of the profile.
TA2	Right corner of the profile.
Te	Structure type. A number from 1 to 15 is worth depending on the type of structure. Ex: Fixed=1; Antaribalta=4; ...... Pre-assembled box=15.
Tfs	Out-of-square type (o= in-square / 1= out-of-square / 2= arched).
Tpt	Frame position type.
Tub	Tubularity difference.

Operators

Name	Description
+	Addition
-	Subtraction
*	Multiplication
/	Division
>	Greater than
<	Less than
>=	Greater than or equal to
<=	Less than or equal to
=	Equal to
<> opp. !=	Different from
&	logical AND
|	logical OR