Appendix III: the variables and symbols
From Opera Wiki
Revision as of 19:52, 26 September 2024 by Lyna.Ferhi (Talk | contribs)
work in progress
Variables
To obtain the insertion of the most suitable accessory, detecting it from an autoselection, to insert the correct end shutter slat, to determine the insertion of profile components, depending on specific measurements, or the last slat with the trim dimension, for all these applications and others, as you know, it is often necessary to make use of the potential of the so-called Variables.
The complete list of variables is given below:
| Nome | Description |
|---|---|
| A | No. of the sash to which the profile or accessory belongs. A=0 is the fixed frame, A=1 is the first sash from the left, A=2 is the second sash from the left, etc... |
| A1 | Left or lower cutting angle of the profile to which the formula is applied or the profile to which the accessory is matched. Vale 45° or 90°. |
| A2 | Right or sup. cutting angle of the profile to which the formula is applied or the profile to which the accessory is matched. Vale 45° or 90°. |
| Alt | Matching profile height |
| Ap | Toward the opening of the structure. Ap=1 is opening to the left; Ap=2 is opening to the right. |
| Av | Glass wing size. |
| Bin | Track (applicable to sliding types). |
| Cam | Profile room value, as recorded on file. |
| Comp | Slat compensation quota |
| Fa | Alternative face. |
| H | Height of the whole type. |
| Ha | Sash height at outer tips. |
| Hav | Rolling height. |
| Hf | Height of individual structure net of glass rebates. |
| Hia | Sash height net of rebates. |
| His | Height of the individual structure net of rebates. |
| Hs | Height of the single structure. |
| Hsa | Door mirror height |
| Hsp | Height of the mounting area of the glass or panel (mirroring). |
| Hsr | Height of the lock. |
| Ht | Traverse height |
| Ht2 | Traverse height |
| Hta | Sash height net of rebates and tooth. |
| Hts | Height of individual structure net of rebates and tooth. |
| L | Width of the whole type. |
| La | Sash width at outer tips. |
| Lato | Side of the structure to which the formula refers. (Side=1 left; Side=2 right; Side=3 high; Side=4 low) |
| Lav | Roll-up width. |
| Lf | Width of the single structure net of glass stops. |
| Li | Length at the tubularity (i.e., net of the stop and tooth) of the profile to which the formula is applied. |
| Lia | Sash width net of rebates. |
| Lis | Width of individual structure net of stops. |
| Lp | Length at the outer tips of the profile to which the formula is applied. |
| Ls | Width of the single structure. |
| Lsa | Door mirror width. |
| Lsp | Width of the mounting area of the glass or panel (mirroring). |
| Lt | Value related to the obtained cut length. |
| Lta | Sash width net of rebates and tooth. |
| Lts | Width of individual structure net of stops and tooth. |
| N | Accessory number.
Present for compatibility with the industrial production version, not active in the basic version. |
| Na | Number of sashes holding the structure. |
| Nst | Number of slats contained in the shutter. |
| Pa | Total door weight. |
| Pav | Shutter weight, detects the total weight of the shutter. |
| Pm | Upright position |
| Pm3 | Upright position. |
| Pos | Accessory mounting position.
Present for compatibility with the industrial production version, not active in the basic version. |
| Posp | Position profile. |
| Pt | Total frame weight. |
| Pz | Total pieces. |
| Qt | Fee calculated by the program.
Present for compatibility with the industrial production version, not active in the basic version. |
| Qt | Fee calculated by the program.
Present for compatibility with the industrial production version, not active in the basic version. |
| Quad | Square footage of the structure. |
| Rdo | Remainder staves, detects the trim measurement of the last stave. |
| Rif | Reference. |
| Rst | Remaining slats, i.e., it is the value remaining after mounting the shutter slats, allows you to determine which end slat you need to mount. |
| Sav | Rolling area, detects the measurement of the rolling area. |
| Spes | Matched profile thickness. |
| Spr | Filling thickness. |
| Sr | Deviation match. |
| TA1 | Left corner of the profile. |
| TA2 | Right corner of the profile. |
| Te | Structure type. A number from 1 to 15 is worth depending on the type of structure. Ex: Fixed=1; Antaribalta=4; ...... Pre-assembled box=15. |
| Tfs | Out-of-square type (o= in-square / 1= out-of-square / 2= arched). |
| Tpt | Frame position type. |
| Tub | Tubularity difference. |
Operators
| Name | Description |
|---|---|
| + | Addition |
| - | Subtraction |
| * | Multiplication |
| / | Division |
| > | Greater than |
| < | Less than |
| >= | Greater than or equal to |
| <= | Less than or equal to |
| = | Equal to |
| <> opp. != | Different from |
| & | logical AND |
| | | logical OR |
