How to edit a typology
From Opera Wiki
Contents |
Editing or adding profiles
from the Design Sheet
Suppose you want to replace the profile that determines the bottom width of your window: Click on the bottom side and open the Edit Side panel:
We click on File:Edit.png and File:Telfisso.png and open the Profile Selections pane
Select the profile and confirm with 
Return to the Edit Side Panel by pressing the button again to confirm the operation and re-enter the Design Sheet.
The change to the profile has been made.
If the change to the type, does not consist of replacing a profile but adding one, repeat the operation, with the only difference that instead of selecting File:Edit.png, you will click the 
button, then repeat the same operations as above.
from the Structure Definition Framework
On the design sheet, press on the File:Edit2.png button and the program will move to the Structure Definition Chart, where you will select the File:Mod.sides.png button and position yourself on the side to be edited; click on to add or on File:Edit.png to replace:
In either case, select the inherent use button. Back on the Structure Definition Chart, press the File:Record.png button to confirm the operation and return to the Design Sheet.
Modification or addition of accessories
dal Foglio di progettazione
In the Design Sheet, we click on the side we are interested in to open the Edit Side panel:
Select the File:Quadroaccessori.png button and, in the Accessories panel click on to add a new one or on File:Edit.png to replace an existing accessory. In either case the following picture will open:
Select File:Code.png and, in the Accessory Selection panel, choose the one you are interested in and confirm with .
The program will return to the Profile Accessories picture press File:Record.png to confirm and to return to the Design Sheet.
from the Structure Definition Framework
On the design sheet, press on the File:Edit2.png button, the program will move to the Structure Definition Framework, where you will select the File:Mod.sides.png button and the File:Arrowdx.png button; now position yourself on the side to be edited; click on File:Quadroaccessori.png
The Frame Accessories panel will be opened: Click on to add or on File:Edit.png to replace and then on File:Code.png
N.B: In performing the latter operation, you will notice that if you have clicked on File:Edit.png, the program will directly open the Accessory Selection pane; if you have clicked , the program will open the Accessory Use paneIn the Accessory Usage pane, choose what you need and go to the Accessory Selection pane. The operator should note that at this point the operations are the same for both cases (adding or editing): choose the accessory and confirm with .
The program will return to the Profile Accessories framework press File:Record.png to confirm and to re-enter the Structure Definition Framework.
Inserting a fixed on an already registered type
The following example will consider a single-sash window to which a fixed will be applied. In the Design Sheet we click the File:Motiplica.png button to open the Multiplication Parameters pane:
Enter the data you are interested in: if you intend to enter a lateral fixed, select the File:Code.png button under Upright and enter the quantity in the Uprights field; if, on the other hand, you intend to enter an upper fixed (as in the following example), select the File:Code.png button under Traverse and enter the quantity in the Traverse field; in both cases, after performing the operations, confirm with .
Suppose, then, that you have chosen to put in a traverse: select the File:Code.png button, the Profile Selection panel will open from which you can choose the one you are interested in and then press to confirm your selection. Following that, enter the amount of traverses and click .
When finished, the structure will appear to you as in the image to the side. As you can see, the top structure is still not correct: to edit it, we click on the File:Edit.png button and then on the top structure to open the Structure Definition Chart; under Structure, we select Fixed and confirm with File:Record.png.
If we have done all the operations well, in the Design Sheet we will see the box on the side. All that remains is to quote the type, for which we refer to the chapter How to insert quotas into a typology'
Insertion of an opener into the opener
The following example will consider a door with a central band, to which a wasistas type will be applied, in the upper mirror; in the Design Sheet we select the File:Apply.png button
The program will open the Type Selection pane: select the type and confirm with .
The mouse will take the shape of a cross, click in the part of the type, where you want to make the application. The Frame Application pane will open: cClick on the File:Mobspecc.png button (by pressing this button, the program will apply in the upper mirroring of the door only the wasistas leaf);
A message will appear File:Quadreplace.png , where we will select the File:Replace.png button. When the operation is complete, the new structure will appear as in the figure.
