Lyna.Ferhi: Created page with '=== Camera === This is the footprint value measured perpendicular to the thickness, excluding only the value of the glass rebate flap. File:zoccolo1.png|Plinth room ex…'

Lyna.Ferhi — Thu, 26 Sep 2024 17:56:33 GMT

Created page with '=== Camera === This is the footprint value measured perpendicular to the thickness, excluding only the value of the glass rebate flap. <gallery> File:zoccolo1.png|Plinth room ex…'

New page

=== Camera ===

This is the footprint value measured perpendicular to the thickness, excluding only the value of the glass rebate flap.
<gallery>
File:zoccolo1.png|Plinth room example
File:zoccolo2.png|Example of a glass plinth room with mortise
</gallery>

=== Beat ===

This is the length of the strike flap.
<gallery>
File:zoccolo3.png|Example of baseboard rebate flap
</gallery>

=== Glass wing ===

This is the length of the glass rebate flap.

=== Glass wing thickness ===

This is the thickness of the glass rebate fin at the part where the gasket is to be mounted.

=== Dente ===

It is the height of the tooth that has influence on the gut.

=== Thickness ===

This is the thickness of the profile measured on the housing side of the glass.

=== Intesta a ===

It tells the program to consider the value set in the '''intest''' box.
{{NB|The addition value related to heading is normally that of the profile tooth to which the profile to be headed is to be connected. However, it is possible to indicate to the program that it should consider '''another addition value''' that is, the one set in the '''intest''' box.}}

=== Header ===
It is the profile elongation value for the bowing operation.
{{NB|This value is considered only if the box '''Headed to''' has been activated.}}
{{BR}}

===Header angle===
Corner composed of the profiles meeting the fixed frame.
{{BR}}

===Enable V-cut===
Indicates that V-cutting is performed in this profile.
{{BR}}

=== Glass cavity ===

This is the space that must remain between the glass and the profile.
{{NB|Typically, this is the shim dowel footprint value. This value is considered when calculating the size of the backfill. However, it is important to know that there is a precedence scale that the program takes into consideration when checking the glass gap value, i.e.: the first value to be examined is the one set on the infill, if this is 0(zero) then the one set on the glazing bead will be examined, if this is also 0(zero) then finally the one set on the frame profile (fixed or sash) will be examined.}}
{{BR}}

=== Dist. min. ruler (Dist. min. ruler) ===
Minimum distance of the ruler from the wall.

=== Sagoma ===
Report the template code.
{{NB|During the phase of assigning the baseboard to the type if the template code is T and the sub-baseboard will not also be added, the program will issue the error message "An inconsistency was detected in the rebates of the mobile frame profiles. Probable opening impossible," see the[[Appendix III: the variables and symbols]] for explanation and solution of this problem.}}
{{BR}}

=== Type M/T ===
Field to filter the selection related to the use of the type of upright/traverse (''All'', ''Upright'', ''Traverse'').
{{BR}}

=== Application type ===
Field to specify which profile application (''All'', ''Frame'', ''Sash'').
{{BR}}

=== Complanarity ===
The function of this box, and directed to the creation of nodes. For profiles that have a coplanarity, such as between the frame and sash, by entering the value in this box, when the program detects the profile image in the Node Creation Box, it takes this value into account, placing the sections with the coplanarity value.
{{BR}}

=== Offset M/T ===
Displacement of the mullion/crossbar elevation from the profile axis.
{{BR}}

=== Separator ===
Sets the profile as a separator.
{{BR}}

=== Asymmetrical ===
The profile is considered asymmetrical with respect to the inner and outer surfaces.
{{BR}}

=== Glass cavity #2 ===
It is triggered by the use of the previous field to determine the lower glass gap height for asymmetrical mullions/ transoms.
{{BR}}

=== Intercapedine ===
This is the space between the floor and the baseboard profile.
<gallery>
File:zoccolo4.png|Example of baseboard cavity
</gallery>

Plinth - Revision history

Lyna.Ferhi: Created page with '=== Camera === This is the footprint value measured perpendicular to the thickness, excluding only the value of the glass rebate flap. File:zoccolo1.png|Plinth room ex…'