Lyna.Ferhi at 20:00, 18 September 2025

Lyna.Ferhi — Thu, 18 Sep 2025 20:00:13 GMT

Lyna.Ferhi: Created page with '===Chamber=== This is the overall value measured perpendicular to the thickness, excluding only the value of the stop flange and the glass flange. File:cameramobile.…'

Lyna.Ferhi — Thu, 18 Sep 2025 19:58:41 GMT

Created page with '===Chamber=== This is the overall value measured perpendicular to the thickness, excluding only the value of the stop flange and the glass flange. </gallery> File:cameramobile.…'

New page

===Chamber===
This is the overall value measured perpendicular to the thickness, excluding only the value of the stop flange and the glass flange.
</gallery>
File:cameramobile.png|Example of the chamber value of a movable frame profile
File:cameramobile2.png|Example of the chamber value of a mortise or sash-glass movable frame profile
</gallery>.

If it is a ''sliding movable frame'', the chamber value is given by the total height excluding the glass stop flap.
</gallery>
File:sliding.png|Example of the chamber value of a sliding movable frame profile
</gallery>.

===Stop flap===
This is the length of the stop flap.
</gallery>
File:flapmobile.png|Example of a stop flap in a movable frame
</gallery>

===Glass flange===
This is the length of the glass stop flange.
<gallery>
File:alettamobile2.png|Example of a glass flange in a movable frame
</gallery>

===Glass flange thickness===
This is the thickness of the glass flange in the area where the gasket must be installed.
<gallery>
File:alettamobile3.png|Example of glass flange thickness
</gallery>

===Tooth===
This is the height of the tooth, which affects the gasket.

{{NB|When calculating the cut length of a transom or mullion, Opera also considers the height of the tooth of the profile to which it must be connected.}}
<gallery>
File:alettamobile4.png|Example of a tooth in a movable frame profile
</gallery>

If it is a through-glass profile, the tooth value will correspond to the negative value of the glass flange height.
</gallery>
File:alettamobile5.png|Example of a tooth in a through-glass profile, value -22
</gallery>

===Thickness===
This is the thickness of the profile measured on the glass housing side.
</gallery>
File:sliding2.png|Thickness of the sliding frame profile
</gallery>.

For an inserted glass profile, this refers to the thickness of the glass housing.

===Interc (Intercavity)===
This is the distance between one profile and another, measured from the start of one chamber to the start of the other.
</gallery>
File:interspace2.png|Example of interspace value between a fixed frame and a sliding frame
</gallery>.

If it is a '''sliding movable frame''', this value must be negative and will correspond to the measure of the fixed frame’s interspace.
</gallery>
File:sliding3.png|Example of interspace value between fixed frame and sliding movable frame
</gallery>

===Inter-glass (space between glasses)===
This is the space that must remain between the glass and the profile.

{{NB|This is usually the value of the spacer blocks. This value is also considered when calculating the mastic dimensions. However, it is important to know that there is a hierarchy the program uses to check the glazing space value: the first value checked is the one set on the mastic; if that is 0 (zero), then the one set on the glazing bead is checked; if that too is 0 (zero), then the one set on the frame profile (fixed or sash) is considered.}}

===Template===
Enter the template code.

{{NB|There are three codes: Z, L, T. Correctly setting the template code allows the program to determine if the node you create is suitable for internal or external openings. For a shutter profile, the template must be set to T in order to display the external opening type.}}

{{BR}}

===Header angle===
Angle formed by profiles meeting the fixed frame.

{{BR}}

===Separator===
Set the profile as a separator.

{{BR}}

===Overlap distance===
Field used to define the overlap distance between the frame and the sash.

{{BR}}

===Coplanarity===
The purpose of this box is to create nodes. For profiles that are coplanar, such as between the frame and the sash, by entering the value here, when the program detects the profile image in the node creation process, it will take this value into account, positioning the sections with the coplanarity value.

Movable frame - Revision history

Lyna.Ferhi at 20:00, 18 September 2025

Lyna.Ferhi: Created page with '===Chamber=== This is the overall value measured perpendicular to the thickness, excluding only the value of the stop flange and the glass flange. File:cameramobile.…'