Lyna.Ferhi: Created page with '{{NB|For this guide, it is assumed that you start with a typology already created to which you will need to add slat filling}} {{BR}} [[File:quadrostru…'

Lyna.Ferhi — Thu, 19 Sep 2024 18:47:58 GMT

Created page with '{{NB|For this guide, it is assumed that you start with a typology already created to which you will need to add slat filling}} {{BR}} [[File:quadrostru…'

New page

{{NB|For this guide, it is assumed that you start with a typology [[How to make a typology|already created]] to which you will need to add slat filling}}
{{BR}}
[[File:quadrostrutturapersiana.png|right|thumb|500 px|Framework defining structure]]

__TOC__

If your typology calls for the filling to be with slats (thus louvered), the operator should keep in mind that the methods of creating the perimeter of both the fixed and the sash, are the same as those already explained. So after inserting the perimeter profiles, and their accessories let's see how and where to act to make the structure become a shutter.
The operation will start from the bottom width of the sash, bring yourself to it by acting to move inside the structure with the buttons [[File:arrowsx.png]] [[File:arrowdx.png]] and positioning yourself by clicking within the area inherent to the bottom width. After clicking the [[Image:keymodified.png]] button and then the [[File:+.png]] button, the following picture will open:

{{BR}}
[[File:quadrosceltaprofilo.png|thumb|left|400px]]
[[File:quadroselezionelamella.png|thumb|right|400 px]]
*We select the [[File:cue.png]] button to open the Profile Selection panel:
*From the next screen, select the profile and confirm with [[File:ok.png]]

The program will return to the Structure Definition Chart, repeat the same operations, and also enter the Terminal Persian Cue [[File:cue2.png]]

{{BR}}
[[File:quadroselezioneportalamella.png|400 px|thumb|left|Terminal latch holder]]
[[File:quadroutilizzoaccessorio.png|300 px|thumb|right|The accessory choice box]]
Now it is necessary to insert the end plate holder:
* On the add bottom profile picture click on the Inner Carryover button: [[File:carryover.png]];
* On the Profile Selection panel, select the saddle holder under Positioner and click [[File:ok.png]]:

Back on the Structure Definition Framework, select the slat and click the [[File:quadroaccessori.png|300 px|thumb|right]] button to open the Shutter Accessories framework Click on [[File:+.png]] and [[File:code.png]] to open the Accessory Use framework

{{BR}}

[[File:selezionekitpersiana.png|400 px|thumb|right]]
In this case you are creating a shutter with movable slats, so by pressing the [[File:autoselect.png]] button, you are going to enter the automatic self-selection for the Handling Mechanisms. If your shutter is with fixed slats, you will instead have to enter the saddles to position the slats by pressing the [[File:kit.png]] button The Accessory Selection panel will open, select the one you want and press [[File:ok.png]] to return to the Shutter Accessories panel. Then press the [[File:record.png]] button and then [[File:ok.png]] to return to the Structure Definition Picture.
At this point to finish all the insertion of the profiles needed for the shutter you will have to move to the upper width to insert the end slat holder Press on the [[File:+.png]] button and on the Add Profile picture press on the [[File:carry-in.png]] button; after selecting the accessory press [[File:ok.png]].

If you have performed all the operations correctly, all you have to do is press the button to move to the next sash (if the type is multi-sash), and repeat the operations you performed for the previous sash.
{{BR}}
[[File:foglioprogettazioneper.png|thumb|left|400 px]]
When you have finished, re-entering the Design Sheet, you will have the type highlighted as in the figure.
The basic operations to create the shutter, as you may have noticed take place in the lower width of the structure sashes. In fact, the program will display the slats in the Design Sheet only if you have entered the slats in the lower widths of the sashes and in the slat accessories, the self-selections of the movement mechanisms, for adjustable shutters, or the saddles in the case of the fixed slat shutter. The operator will therefore have to take great care in inserting in the right position especially these two components.

{{BR}}
== Insert the end plate holders to the center band ==

[[File:gestioneMTI.png|350 px|thumb|right|MTI Choice Window]]
You have created a louvered French Window and applied a center band to it, you now have the need, to apply the carry-over for the end slat. From the Design Sheet click on the fascia, the following picture will open:

Click on [[File:MTI.png]] and open the Mullion-Crossbeam and Muntin Management panel:

[[File:finestragestioneMTI.png|thumb|left|400 px]]

Click in the center of the louver (Pers=ON), a small box will appear from which you must select the [[File:Traverse.png]] button.

The Profile Selection pane will open at this point: after selecting the desired sash click [[File:ok.png]] and you will be taken back to the Mullion-Crossbeam and Inglesina Management pane; a mask will indicate that the profile has matching accessories:

[[File:quadroaccessoriabbinati.png|400 px|thumb|right]]

Select the [[File:keyosi.png]] button and return to the Manage mullions-crossbars and muntin bars panel.

{{BR}}
[[Image:quadroriporti.png|thumb|left|300px]]
* Now we need to insert the Sup/Dx and Inf/Sx carryovers: click for both on [[File:code.png]] and choose Positioner; click [[File:ok.png]].
* We select [[File:ok.png]] and repeat the operation for the lower carryover. We click on [[File:=.png]] to duplicate the carryovers in the second shutter.

{{BR}}

[[File:foglioprogettazionepersiana2.png|400 px|thumb|right]]
When you have finished operations, press the [[File:record.png]] button located in the upper right-hand corner of the Mullion Management crossbars and muntin bars panel. This is what appears in the Design Sheet:

{{NB| if we select the [[File:Buttononoffpersiana.png]] button, position ourselves on a part of the shutter, and click on [[File:record.png]], we disable the display of that part of the shutter}}

{{BR}}

== Related items ==
*[[How to edit a typology]]
*[[Archive Typology]]

[[Category: JM/Manuale]]

How to make a shutter - Revision history

Lyna.Ferhi: Created page with '{{NB|For this guide, it is assumed that you start with a typology already created to which you will need to add slat filling}} {{BR}} [[File:quadrostru…'