Monica.Sanna: moved Viewing Nodes to Node Definition Window

2025-07-08T15:17:09Z

moved Viewing Nodes to Node Definition Window

← Older revision

Revision as of 15:17, 8 July 2025

Lyna.Ferhi: Created page with 'Example of a structure with nodes already created {{NB|To access this pane in Opera Job Management: from the types archive, aft…'

2024-09-25T21:19:26Z

Created page with 'Example of a structure with nodes already created {{NB|To access this pane in Opera Job Management: from the types archive, aft…'

New page

[[File:foglioprogettazionenodi1.png|500 px|thumb|Example of a structure with nodes already created]]
{{NB|To access this pane in Opera Job Management: from the types archive, after selecting a type press the button [[Image:tastoprogettazione.png]]}}

To view the nodes of one's structure, one must press the [[File:tastonodi.png]] button.<br> There are basically two viewing modes: the first allows one to view the individual node in the profile by clicking on it, while the other allows one to view the nodes by drawing a line in the type with a horizontal or vertical section.<br> Let us now look at the viewing modes in detail:

{{BR}}
==Single knot==
[[File:visualizzazionesingolonodo.png|thumb|400px|Display of the selected side node]]
This type of view is obtained from the [[Design Sheet]], by activating the node key [[File:keynodes.png]] and clicking one side of the structure on which you want to view the node.

'''This display allows both to manage the correct display of the node, but more importantly to match a thermal value to the node for CE marking''' (See "Add Certificate" button).

*[[image:tastoarchivio.png]]: opens the[[Node Archive|Node Archive]]
*[[image:tastodettaglinodi.png]]: allows you to review the node in the [[Node Definition|Node Definition Box]] for possible editing and then through the [[File:SaveQdN.png]] button save them within the [[Node Archive|Node Archive]]
*[[image:tastostampa6.png]]: allows the node to be printed at a scale of 1:1
*[[image:tastoaggiungiacertificato.png]]: opens the [[Series Certification Node Archive]] and allows the node to be associated with a certificate for transmittance calculation even if the node is not saved in the archive. Once matched, the following key will be shown [[image:keyvisualizecertificate.png]]
{{NB|In the event that the fill icon has never been created in the archive, the program will open the [[Compose Fill Icon]] window that will allow the drawing to be created.}}

*[[image:tastomodificaoggettonodo.png]]: by clicking on one of the objects in the right column, you can go into editing the object, to associate a reference point, create an entitie, or to make any change to the drawing itself.
'''''See also. [http://youtu.be/gm52M3cJ8f0?list=PLsWGwm9K4bfmf5jit8w_VlD0V1OJHvF62 Changelog #1569]'''''
{{BR}}

==Section nodes==
It is possible to see the nodes on both sides (left and right, bottom and top) by drawing a straight line, holding down the left mouse button and sliding it across the work surface so that it cuts the type in width or height as shown in the example:

{|
|[[File:foglioprogettazionenodi2.png|thumb|500px|Example of drawing the straight line]]
|[[File:nodi.png|thumb|390px|Window side knots]]
|}

*[[Image:tastostampa8.png]]: prints the highlighted nodes
*[[Image:tastodxf.png]]: loads a DXF file from the file system
*[[Image:tastoopendxf.png]]: opens nodes in dxf format with the default viewer program set in your operating system
*[[Image:tastizoom2.png]]: allow you to adjust the magnification of the preview of the displayed nodes



[[Category: JM/Manuale]]

Node Definition Window - Revision history

Monica.Sanna: moved Viewing Nodes to Node Definition Window

Lyna.Ferhi: Created page with 'Example of a structure with nodes already created {{NB|To access this pane in Opera Job Management: from the types archive, aft…'