Lyna.Ferhi: Created page with 'The setup framework of technical prints TOC The following are the steps for managing 3D rendering: ==Installation== […'

2024-09-23T20:41:26Z

Created page with 'The setup framework of technical prints __TOC__ The following are the steps for managing 3D rendering: ==Installation== […'

New page

[[Image:finestrasetupstampetecniche.png|thumb|500px|The setup framework of technical prints]]
__TOC__

The following are the steps for managing 3D rendering:

==Installation==
[[Image:messaggiosetupmediapack.png|thumb|500px]]
* Go to ''Workshop --> Technical Print Setup''

* Click on the button [[image:tastorendering3d.png]]
{{NB| If not done before, you will be prompted to download and install the ''Media Pack'' program}}

*Perform the installation procedure (if necessary)
<gallery>
image:instmediapack1.png| ''Step 1''
image:instmediapack2.png| ''Step 2''
image:instmediapack3.png| ''Step 3''
image:instmediapack4.png| ''Step 4''
image:instmediapack5.png| ''Step 5''
</gallery>

{{BR}}

==Rendering configuration==
[[Image:finestrasetuprendering.png|thumb|500px|right|The 3D rendering setup framework]]
* Go to ''Workshop --> Technical Print Setup'' and press [[image:tastorendering3d.png]]. The [[Setup rendering| rendering setup]] panel will open. Within it you can set the parameters of the 3D type previews that Opera is to generate.

==Image generation==

3D image generation is done within the individual type in the job order.

{{NB| In order to display the 3D correctly, you need to correctly construct nodes, so see the chapter in our [[Node Archive]] guide.}}

* Go to ''Job Orders'' --> ''Management'' to open the job order list
* Select the desired job order (or first [[How to make a job order|create a new one]]) and press the [[image:keydiverse.png]] button. The list of types in the job order will be shown.
* Click on the [[Image:keycards.png]] button and choose the type of 3D print (Patterns or Abacus) and proceed with printing. The program will propose to you after rendering the 3D images in the chosen prints.
{{NB| The rendering time may vary depending on the image chosen, the performance of the pc in use and the parameters chosen}}
[[image:temporendering.png|thumb|left|300px]]
{{BR}}

==Stampe==
[[image:preventivo3d.png|thumb|400px|an example of a 3D quote]]
It is possible to make different types of prints:

#Abaco 3D
#Schemi 3D

To activate these printouts follow the steps below:

* Bring yourself within the framework of [[Job order|management]]
* Press the [[image:keychecks.png]] button. This will open the window of [[Job prints|job prints]]
* Select the desired print type (''Abacus 3D types'' / ''Schematic 3D types'') and press [[image:tastook.png]]

<gallery>
image:schema3d.png|an example of a 3D schematic
image:abaco3d.png| an example of a 3D abacus
</gallery>

The following steps should be followed to make a 3D image quote print:

* Take yourself to the ''Archives'' framework --> ''Documents''
* Select the document normally used for printing the quote and duplicate it by pressing the [[image:equal key.png]]Select the document normally used for printing the quote and duplicate it by pressing the [[image:equal key.png]]
* Give a different name to the newly created document (''example: 3D Quote'')
* Edit the newly created document, replacing the macro ''//Abaco//'' with ''//Abaco3D//''
* Save the document
{{NB| This should be done only once}}

Whenever you want to print a 3D quote, from the [[Job Documents|Job Documents]] panel, select the 3D quote and print normally.


[[Category:JM/Manuale]]

How to manage 3D prints - Revision history

Lyna.Ferhi: Created page with 'The setup framework of technical prints __TOC__ The following are the steps for managing 3D rendering: ==Installation== […'

Lyna.Ferhi: Created page with 'The setup framework of technical prints TOC The following are the steps for managing 3D rendering: ==Installation== […'