http://wiki.operacompany.com/en/index.php?action=history&feed=atom&title=How_to_make_a_porthole 2026-06-02T22:16:56Z Revision history for this page on the wiki MediaWiki 1.15.4 http://wiki.operacompany.com/en/index.php?title=How_to_make_a_porthole&diff=2909&oldid=prev 2024-09-19T19:25:01Z

<p>Created page with &#39;__TOC__ In this chapter we will explain how to create a porthole from a fixed, an opening or a transom (the only possible types). {{NB| Before we begin, it is important to make …&#39;</p> <p><b>New page</b></p><div>__TOC__<br /> <br /> In this chapter we will explain how to create a porthole from a fixed, an opening or a transom (the only possible types).<br /> {{NB|<br /> Before we begin, it is important to make sure that the profile chunks we want to edit into a porthole are all the same, and to do this we refer you to the chapter [[How to edit a type]].We also recommend that you save the porthole types you create in your Types Archive.}}<br /> <br /> The management of a porthole is always done through the dimensioning function, that is, by pressing the [[File:Quotation key.png]] button found both in the Design Sheet and in the General Data pane of the type. <br /> <br /> {{BR}}<br /> == '''Oblò fisso''' ==<br /> [[File:foglioprogettazioneoblofisso.png|500 px|thumb|left|Starting structure for a fixed porthole]]<br /> Once we have selected a fixed type and have pressed the [[Image:Quotation key.png]] button, we click on the [[File:adarco.png]] button and open the Arch Data panel, where we will select porthole through the menu opened with the [[File:arrowgiu.png]] button.<br /> <br /> [[File:datiarco.png|thumb|right]]<br /> <br /> Click [[File:ok.png]] in the Arc Data frame and in the Design Sheet the type will be as shown in the figure below.<br /> <br /> {{BR}}<br /> [[File:foglioprogettazioneoblofisso2.png|500 px|thumb|left|Struttura ultimata con oblò fisso]]<br /> <br /> After changing the porthole measurements in the Type Dimensions field (if it is necessary), click on [[File:ok.png]], exit the Design Sheet with the [[File:x.png]] button, and record the type in the archive.<br /> <br /> {{BR}}<br /> <br /> == '''Oblò a bilico''' ==<br /> <br /> [[File:foglioprogettazioneoblobilico.png|500 px|thumb|left|The starting structure]]<br /> <br /> Once we have selected a porthole type and pressed the [[Image:Quotation key.png]] button, we click on the [[File:adarco.png]] button and open the Arch Data panel, where we will select porthole through the menu opened with the [[File:arrowgiu.png]] button.<br /> <br /> [[File:datiarco.png|thumb|right]]<br /> <br /> Click [[File:ok.png]] in the Arc Data frame and in the Design Sheet the type will be as shown in the figure below:<br /> <br /> {{BR}}<br /> [[File:foglioprogettazioneoblobilico2.png|500 px|thumb|left|The completed structure with hover portholes]]<br /> <br /> After editing the porthole measurements in the Type Dimensions field (if needed) and revising the movable frame accessories (hinges), click on [[File:ok.png]], exit the Design Sheet with the [[File:x.png]] button, and register the type in the archive.<br /> <br /> {{BR}}<br /> <br /> == '''Oblò a vasistas con traverso''' ==<br /> <br /> [[File:foglioprogettazioneoblotraverso.png|500 px|thumb|left|The starting structure]]<br /> Before operating on the structure to create a porthole, it is necessary to add a traverse to the chosen type. To do this we click on the [[File:multiply.png]] button and open the Multiplication Parameters pane, enter a transom and confirm. <br /> [[File:quadroparametrimoltiplicazione.png|400 px|thumb|right]]<br /> <br /> {{BR}}<br /> [[File:foglioprogettazioneoblotraverso2.png|500 px|thumb|left|The structure with a traverse]]<br /> The frame will look like the image on the side. Now we need to edit it to transform the lower part so that it is a fixed frame. To do this we click on the [[File:edit.png]] button and in the Design Sheet we click on the profile to be edited; the '''Structure Definition Framework''' will open and, in the '''Structure''' field, we choose ''Fixed'' and register.<br /> <br /> {{BR}}<br /> [[File:foglioprogettazioneoblotraverso3.png|500 px|thumb|left|The structure with the fixed frame at the bottom]]<br /> At this point we press the [[Image:Quotation key.png]] button and click on the [[File:adarco.png]] button. This will open the Arch Data panel, where we will select porthole through the menu opened with the [[File:arrowgiu.png]] button.<br /> [[File:datiarco.png|thumb|right]]<br /> <br /> {{BR}}<br /> [[File:foglioprogettazioneoblotraverso4.png|500 px|thumb|left|The completed structure]]<br /> Back in the Design Sheet, after changing the porthole measurements in the Type Dimensions field (if necessary) the completed structure will appear<br /> {{BR}}<br /> <br /> =='''Related items'''==<br /> *[[How to make a typology]]<br /> *[[How to edit a typology]]<br /> *[[Archive Typology]]<br /> <br /> <br /> [[Category: JM/Manuale]]</div>

Lyna.Ferhi